Mr. Electrician, are you;
Too busy to figure out those confusing platform wiring diagrams?
Too busy to locate all those little bits needed to make up the control panel?
Frustrated trying to get all those safety inter locks to work properly?
Would you like free phone support if problems arise?
The CSL Platform Drive Control Panel is the answer, check out these features.
1. Simple number by number interconnection between the console(s) and PDCP.
2. Low Voltage (24 Volt) supply built in for controls to the console.
3. Variable Speed and Direct-On-Line (DOL) built in with a switch on the cabinet.
4. All safety and operation switches including the Emergency Stop, Pull switch, Breech switch,
Forward and Reverse all work in both Variable Speed and DOL
5. Wash cycle. Platform returns to wash position at high speed in either forward or reverse
and is disabled until the "Wash" switch is turned back to "Milk". Micro switch supplied.
6. Terminal with. loop to connect a wash hose hang-up switch if required.
7. Terminal with loop to connect an auto-reverse of the breech switch if required.
8. Motor overload protection for two or four motor systems built in (specify motors when
ordering).
9. Clear lid 1P55 cabinet with key locks for mounting adjacent to or in the main switchboard.
10. LED indication on all control relays to show status at a glance without opening cabinet.
11. Cabinet mounting frame and wiring built to take the Danfoss VLT28OO controller supplied
for platform control. Send us the controller and we will mount, wire and test for you.
12. 0800 phone support available 24 hours, seven days a week.
13. Saves time in installing and commissioning platform controls on site.
14. Costs no more (probably less) than if the on-site electrician makes the controls.
15 Manufactured to a standard nation-wide Telarc Q-Base Quality Assurance system by a
company specializing in Dairy Automation.
Comments by an Electrical Contractor
"We found that every time we sent a new tradesman and apprentice to wire a new platform, they took about two days to figure out and connect the control wiring and sometimes still didn't have the platform safeties working properly. With these control panels we have the installation time down to four hours and we know it will work correctly and safely - no OSH worries. We have found also that the cost of this panel is about the same as if we were to do it all ourselves (even with a tradesman who takes less than two days !)"
Too busy to figure out those confusing platform wiring diagrams?
Too busy to locate all those little bits needed to make up the control panel?
Frustrated trying to get all those safety inter locks to work properly?
Would you like free phone support if problems arise?
The CSL Platform Drive Control Panel is the answer, check out these features.
1. Simple number by number interconnection between the console(s) and PDCP.
2. Low Voltage (24 Volt) supply built in for controls to the console.
3. Variable Speed and Direct-On-Line (DOL) built in with a switch on the cabinet.
4. All safety and operation switches including the Emergency Stop, Pull switch, Breech switch,
Forward and Reverse all work in both Variable Speed and DOL
5. Wash cycle. Platform returns to wash position at high speed in either forward or reverse
and is disabled until the "Wash" switch is turned back to "Milk". Micro switch supplied.
6. Terminal with. loop to connect a wash hose hang-up switch if required.
7. Terminal with loop to connect an auto-reverse of the breech switch if required.
8. Motor overload protection for two or four motor systems built in (specify motors when
ordering).
9. Clear lid 1P55 cabinet with key locks for mounting adjacent to or in the main switchboard.
10. LED indication on all control relays to show status at a glance without opening cabinet.
11. Cabinet mounting frame and wiring built to take the Danfoss VLT28OO controller supplied
for platform control. Send us the controller and we will mount, wire and test for you.
12. 0800 phone support available 24 hours, seven days a week.
13. Saves time in installing and commissioning platform controls on site.
14. Costs no more (probably less) than if the on-site electrician makes the controls.
15 Manufactured to a standard nation-wide Telarc Q-Base Quality Assurance system by a
company specializing in Dairy Automation.
Comments by an Electrical Contractor
"We found that every time we sent a new tradesman and apprentice to wire a new platform, they took about two days to figure out and connect the control wiring and sometimes still didn't have the platform safeties working properly. With these control panels we have the installation time down to four hours and we know it will work correctly and safely - no OSH worries. We have found also that the cost of this panel is about the same as if we were to do it all ourselves (even with a tradesman who takes less than two days !)"
C.S.L. Platform Drive Module
